|
|
|
Mechanical Engineering
602
|
Advanced Robotics
|
|
Review of kinematics and dynamics of serial-link manipulators and the Euler-Lagrange method. Kinematics and dynamics of parallel manipulators. Position, force, and impedance control of manipulators. Lyapunov stability. Feedback linearization. Advanced path and trajectory planning. Redundant manipulators and trajectory optimization.
Course Hours:
3 units; (3-0)
Prerequisite(s):
Mechanical Engineering 505.
|
back to top | |
|
Mechanical Engineering
603
|
Physical Fluid Dynamics
|
|
Physical phenomena of incompressible fluid motion for a variety of flows, e.g. pipe and channel flow, flow past a cylinder, and convection in horizontal layers. The derivation of the basic equations of fluid mechanics using Cartesian tensor notation. High and low Reynolds number flows including some solutions of the viscous flow equations, inviscid flow, and elementary boundary layer theory. Thermal free convective flows.
Course Hours:
3 units; (3-1T)
|
back to top | |
|
Mechanical Engineering
605
|
Combustion Processes
|
|
Review of thermodynamics and chemical kinetics of combustion. Fluid mechanics, heat and mass transfer in combustion phenomena. Autoignition and source ignition, flames and detonation. Quenching and explosion hazards, flammability and detonation limits. Heterogeneous combustion, combustion practical systems, combustion as affecting pollution and efficiency, some experimental combustion methods.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
607
|
Mechanics of Compressible Flow
|
|
One-dimensional steady and unsteady motion with application to the analysis of supersonic nozzles, diffusers, flow in conduits with friction, shock tubes. Two-dimensional flow of ideal fluid. Small perturbation theory, method of characteristics with application to design of supersonic nozzles. Waves in two-dimensional flow.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
613
|
Research Seminar I
|
|
Students will develop written and oral communication skills required to disseminate their technical research results and to receive formative feedback on performance.
Course Hours:
3 units; (3S-0)
NOT INCLUDED IN GPA
|
back to top | |
|
Mechanical Engineering
614
|
Reliability-based Engineering
|
|
Theory and practical implementation of statistics in reliability; mean time to failure; availability; reliability block diagrams; root cause analysis; load-strength interference; first-order reliability methods; time to failure for selected failure mechanisms; system reliability model; machine learning for reliability engineering and safety.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
615
|
Sensors, Data and Signal Analysis
|
|
Basic principles relating to measurement systems and data and signal processing. Measurement system behaviour. Application of probability and statistics to measurement systems. Dynamics and selection of various measuring devices for pressure, temperature, stress and acceleration. Uncertainty analysis. Data acquisition and signal conditioning.
Course Hours:
3 units; (3-3/2)
|
back to top | |
|
Mechanical Engineering
616
|
Environmental Fluid Mechanics
|
|
Overview of fluid mechanics fundamentals; Boundary layer theory; Turbulence theory; Turbulent structures; Simulation of environmental flow and transportation of air pollutants; Dynamics of particulates dispersed in gases; Environmental applications (Two-phase flow and particulate removal; Turbulence and dispersion in low atmosphere).
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 616 and any of Environmental Engineering 616, 619.11 (Environmental Fluid Mechanics) or Mechanical Engineering 619.06 (Environmental Fluid Mechanics) will not be allowed.
|
back to top | |
|
Mechanical Engineering
618
|
Methods in Uncertainty Quantification and Machine Learning for Scientific Engineering Applications
|
|
An introduction to the stochastic modeling of dynamical systems. Methods for the application of stochastic differential equations in various domains including target tracking and mechanical vibrations and their use in parameter estimation, filtering, smoothing, and inverse problems. Introduction to popular methods for machine learning in scientific applications. Main emphasis is put on solution methods rather than analysis and theoretical properties of equations.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
619
|
Special Problems
|
|
Designed to provide graduate students, especially at the PhD level, with the opportunity of pursuing advanced studies in particular areas under the direction of a faculty member. Students would be required to consider problems of an advanced nature.
Course Hours:
3 units; (3-0)
MAY BE REPEATED FOR CREDIT
|
back to top | |
|
Mechanical Engineering
620
|
Geomatics Engineering for Pipeline Systems
|
|
Provides both the classical basis to geomatics as a powerful tool in the design and management of pipelines as well as the cutting-edge view of the discipline as a digital technology.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 620 and 619.10 (Geomatics Engineering for Pipeline Systems) will not be allowed.
|
back to top | |
|
Mechanical Engineering
622
|
Pump and Compressor Stations
|
|
Basic role of pump and compressor stations on a pipeline. Design and performance of centrifugal, screw and reciprocating compressors and centrifugal and positive displacement pumps. Design and performance of drivers including gas turbines, engines and electric motors. Design and functions of auxiliary systems, including bearings and lubrication systems, seals and sealing systems and instrumentation and controls. Design studies for acoustic/mechanical and torsional analysis. Pump and compression station equipment and functions.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 622 and 619.11 (Pump and Compression Stations) will not be allowed.
|
back to top | |
|
Mechanical Engineering
624
|
Fundamentals of Pipeline Economics
|
|
Provides students with a fundamental understanding of engineering economics, including decision-making processes and life-cycle assessment in application to pipeline systems.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 624 and 619.12 (Fundamentals Pipeline Economics) will not be allowed.
|
back to top | |
|
Mechanical Engineering
626
|
Corrosion Science in the Pipelines Industry
|
|
Overview of corrosion in the pipeline industry with emphasis on the underlying science, including thermodynamics and kinetics of electrochemical processes, corrosion prevention and mitigation by materials selection, inhibition, coatings and cathodic protection. Implications for integrity management will also be discussed.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 626 and 619.16 (Corrosion Science in the Pipelines Industry) will not be allowed.
|
back to top | |
|
Mechanical Engineering
628
|
Pipeline Coatings
|
|
Introduction to the fundamental properties and structure of coatings, as well as applications in the pipeline industry. Applications of coating technology in integrity maintenance of the various structural facilities. Computer assisted coatings project management programs will be introduced.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 628 and 619.27 (Pipeline Coatings) will not be allowed
|
back to top | |
|
Mechanical Engineering
630
|
Fundamentals of Liquid Hydraulics in Pipeline Systems
|
|
Introduction to the fundamentals of liquid hydraulics in pipeline systems. Topics include petroleum fluids, design elements and economics, mechanical design, fluid mechanics fundamentals, pipeline hydraulics, isothermal flow, pumping requirements, centrifugal and reciprocating pumps, operations and maintenance design, and design optimization.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 630 and 619.49 (Fundamentals of Liquid Hydraulics in Pipeline Systems) will not be allowed.
|
back to top | |
|
Mechanical Engineering
631
|
Numerical Methods for Engineers
|
|
Introduction, mathematical modelling, sources of errors in the process of numerical analysis and solution methodology; Elements of numerical analysis, Taylor series, round-off error, truncation error, concept of stability, consistency and convergence; Linear algebra, normal forms, Gauss elimination method, LU-decomposition, tridiagonal systems of equations; iterative methods, Jacobi, Gauss-Seidel, SOR, SSOR methods, conjugate gradient methods and preconditioning and principles of the multi-grid methods; Elliptic "equilibrium" equation, Laplace and Poisson equations, finite difference and finite control volume concepts and stability analysis; Parabolic equations: explicit, implicit and Crank-Nicolson methods, time-splitting method, method of lines, Stability analysis; Hyperbolic equations; Introduction to other methods; future challenging problems.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 631 and Environmental Engineering 625 will not be allowed.
|
back to top | |
|
Mechanical Engineering
632
|
Fundamentals of Gas Hydraulics in Pipeline Systems
|
|
Applications of fundamental fluid mechanics concepts to pipelines conveying compressible media (gases). Strategies for describing the gas-dynamics of pipeline systems and networks are developed, as well as the influence of gas properties and pipeline operating characteristics on component selection and operating parameters.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 632 and 619.40 (Fundamentals of Gas Hydraulics in Pipeline Systems) will not be allowed.
|
back to top | |
|
Mechanical Engineering
633
|
Mathematical Techniques for Engineers
|
|
Application of mathematical techniques to the solution of ordinary and partial differential equations arising in engineering problems. Methods that will be considered are: separation of variables, method of characteristics, transform methods and complex variable methods.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
634
|
Pipeline Geotechnical Engineering
|
|
Introduction to applications of geotechnical engineering in design and construction of oil and gas pipelines. Geohazard assessment and mitigation methods and issues around pipe/soil interaction will be discussed, as well as the relevant codes, standards and industry guidelines for pipelines.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 634 and 619.57 (Pipeline Geotechnical Engineering) will not be allowed.
|
back to top | |
|
Mechanical Engineering
636
|
Structural Analysis of Buried Steel Pipeline Systems
|
|
An introduction to stress analysis of buried pipelines through hand calculations, spreadsheets, and stress analysis software. Pipeline code requirements are discussed. Individual practices and industry examples are used.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 636 and 619.67 (Analysis of Buried Steel Pipeline) will not be allowed.
|
back to top | |
|
Mechanical Engineering
637
|
Thermal Systems Analysis
|
|
Fundamentals of thermodynamics, fluid mechanics, heat transfer and combustion; Modelling of thermophysical properties; Second law of thermodynamics, concept of entropy generation and exergy analysis; Minimizing environmental impact; Advanced design and analysis of heat exchangers, co-generation, renewable energy systems, and propulsion systems.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 637 and Environmental Engineering 673 will not be allowed.
|
back to top | |
|
Mechanical Engineering
639
|
Numerical Methods for Computational Fluid Dynamics
|
|
Review of solution techniques for ordinary differential equations. Stability, consistency and convergence. Order of accuracy. Fourier methods for stability. Numerical techniques for one-, two- and three-dimensional linear parabolic problems. Courant condition. Implicit and semi-implicit schemes. Boundary conditions for parabolic problems. Techniques for linear hyperbolic problems. CFL condition. Characteristics, domain of dependence and domain of influence. Boundary conditions for hyperbolic problems. Non-linear conservation laws. The Burger's equation as a test problem. Strong and weak solutions. Conservative and integral forms. Conservative schemes. Entropy condition. Godunov theorem and flux limiters. Godunov, ENO and TVD schemes. Implementation in gas dynamics.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
640
|
Stress Corrosion Cracking of Materials
|
|
Fundamentals of stress corrosion cracking (SCC) of materials and the factors contributing to SCC from environmental, metallurgical and mechanical sources. Various testing techniques to study and/or evaluate SCC will also be discussed.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 640 and 619.90 (Stress Corrosion Crack Behaviour) will not be allowed.
|
back to top | |
|
Mechanical Engineering
641
|
Advanced Control Systems
|
|
Introduction to multivariable systems; state space models; analysis of linear systems; stability; Cayley-Hamilton theorem; controllability and observability; state feedback control; pole placement designs; introduction to linear optimal control and estimation; Kalman filtering; separation theorem and duality; performance specifications; controller reduction concepts; introduction to robust control.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
642
|
Construction and Project Management
|
|
Construction sequences for large pipe; clearing, grading, trenching, stringing; techniques for smaller pipe and narrower right of way; joining of HDPE; right of way; salvage, automatic welding; ultrasonic and radiographic inspection; record keeping; as built drawings and alignment sheets; hydrostatic testing; purging and commissioning; ground bed installation; cathodic protection.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
643
|
Optimal and Adaptive Control
|
|
Discrete time and sampled-data system models and properties; discrete time domain controller design principles; system identification using least-squares analysis; self-tuning control; indirect adaptive control; model reference adaptive control; sliding mode control in continuous and discrete time; optimal design of sliding mode controllers; sensitivity functions and their role in control theoretic performance specification; robust stability and robust performance objectives; Kharitonov stability.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
644
|
Welding and Joining Processes
|
|
Welding and joining methods and inspection techniques. Some of welding includes fusion welding (e.g., MIG, TIG, stick welding, SAW) and non-fusion welding (e.g., friction welding). Other joining methods, such as soldering, brazing, adhesives, fasteners, and interference fits. Quality control and inspection techniques for welding (NDE).
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
647
|
Finite Element Method
|
|
One- and multi-dimensional problems in linear and steady heat conduction and elasticity. Emphasis on: strong and weak formulation of the boundary value problems (BVP) and their approximation by Galerkin’s method; fundamentals of finite element interpolation and construction of interpolation functions for a variety of multi-dimensional element shapes; existence and uniqueness of the solution; error estimates; finite element arrays and data structures employed in computer programs; numerical integration techniques; and mesh construction.
Course Hours:
3 units; (3-2)
Antirequisite(s):
Credit for Mechanical Engineering 647 and either 547 or 619.01 (The Finite Element Method) will not be allowed.
|
back to top | |
|
Mechanical Engineering
650
|
Mobile Robotics
|
|
Overview of unmanned vehicles, mobile robot locomotion systems, wheeled rovers, walking machines, mobile-manipulators, mobile robot sensors and actuators, simulation, modelling and analysis of mobile robot behaviour, robot-environment interaction analysis, 2D navigation techniques and localization, mobile robot simulation tools.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
653
|
Advanced Continuum Mechanics
|
|
Review of linear algebra: vector spaces, linear maps, tensors; affine spaces: coordinate systems and differential calculus; kinematics of continua: deformation and strain tensors, deformation and strain rates; balance equations: mass, linear momentum, angular momentum, energy; entropy inequality; stress tensors; stress rates; stress power and conjugated stress-strain pairs; constitutive theory: constitutive axioms, hyperelastic solids, perfect and Newtonian fluids.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 653 and 619.32 (Advanced Continuum Mechanics) will not be allowed.
|
back to top | |
|
Mechanical Engineering
661
|
Mechatronics Design Laboratory I
|
|
A hands-on laboratory experience in the design and analysis of electro-mechanical components. Introduction to microprocessor-controlled electromechanical systems. Laboratory projects to configure, design, and implement a succession of mechatronic systems. Topics of lectures and labs include aliasing, quantization, electronic feedback, power amplifiers, digital logic, encoder interfacing, and motor control.
Course Hours:
3 units; (1-4)
Antirequisite(s):
Credit for Mechanical Engineering 661 and any of 560, 561, 619.47 (Advanced Mechatronics I) or 660 will not be allowed.
|
back to top | |
|
Mechanical Engineering
662
|
Mechatronics Design Laboratory II
|
|
Continuation of Mechanical Engineering 661, involving more sophisticated and in-depth topics in mechatronic systems design explored through laboratory exercises, and complemented by selected lecture topics including practical control aspects of saturation and tuning and machine learning introduction.
Course Hours:
3 units; (1-4)
Antirequisite(s):
Credit for Mechanical Engineering 662 and any of 560, 562, 619.48 (Advanced Mechatronics II) or 660 will not be allowed.
|
back to top | |
|
Mechanical Engineering
663
|
Advanced Muscle Mechanics and Physiology
|
|
A look at problems associated within muscle mechanics and contractility. Also the use of muscle mechanics as a scientific discipline to critically learn and evaluate the scientific process. Basic anatomy and physiology of muscle contraction including the cross-bridge theory, and the force-length, force-velocity and force-time relationships of actively and passively contracting muscles will also be covered.
Course Hours:
3 units; (3-0)
Prerequisite(s):
Consent of the Department.
Antirequisite(s):
Credit for Mechanical Engineering 663 and either Kinesiology 663 or Medical Science 663 will not be allowed.
|
back to top | |
|
Mechanical Engineering
664
|
Pipeline Design
|
|
Function and types of pipeline systems; gathering, transmission, distribution. Design parameters and procedures: supply and demand considerations; design life; capacity planning; system planning and facilities. Hydraulic design. Mechanical design. Geotechnical design.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
665
|
Advanced Materials Engineering
|
|
Covers a variety of material aspects and provides a fundamental understanding of Materials Science and Engineering. Emphasizes the understanding of advanced dislocation theory and its application in illustration of diffusion, deformation and fracture of metals. Fundamentals of material strengthening mechanisms are covered. Practical aspects that are relevant to material uses and failures, such as environmental-induced cracking, creep, fatigue, strain aging and corrosion, are discussed. Typical surface analysis techniques for material characterization are introduced.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
667
|
Fracture Mechanics
|
|
Basic fracture theory, failure criteria, overview of fracture mechanics, brittle and ductile failure, crack tip parameters, geometric considerations, methods of analysis, fracture toughness and testing standards. Applications in design, fatigue subcritical crack growth, creep and impact.
Course Hours:
3 units; (3-0)
Antirequisite(s):
Credit for Mechanical Engineering 667 and either 619.74 (Failure and Fracture Mechanics Pipeline Industry) or 638 will not be allowed.
|
back to top | |
|
Mechanical Engineering
668
|
Pipeline Economics
|
|
Macroeconomics of system supply and demand, open season procedures, optimized sizing, J curves; CAPEX, OPEX, taxation, leasing, depreciation and capital cost allowance, developing revenue requirement, cost of service. Salvage and end of life cost. For utilities Allowance for Funds Used During Construction (AFUDC).
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
669
|
Fatigue of Materials
|
|
History and origin of fatigue. Stress life, strain life and fracture mechanics approaches. Low and high cycle fatigue. Low and high temperature fatigue. Combined stresses, initiation, and propagation of cracks. Environmental and statistical effects. Testing techniques and variables. Design and specific material behaviour. Mechanisms of fatigue.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
670
|
Aerodynamics
|
|
Kinematics and dynamics of viscous and inviscid flow; airfoil dynamics including thin airfoil theory and lifting line theory, finite wings, panel methods and airfoil parameters. Boundary layer theory and boundary layer control as applied in aerodynamics. Introduction to computational fluid dynamics and experimental aerodynamics.
Course Hours:
3 units; (3-2/2)
Antirequisite(s):
Credit for Mechanical Engineering 670 and any of 519.06 (Aerodynamics), 570 or 619.31 (Aerodynamics) will not be allowed.
Also known as:
(Mechanical Engineering 570)
|
back to top | |
|
Mechanical Engineering
672
|
Computational Fluid Dynamics
|
|
Topics include: finite volume and finite element approximations; overview of turbulence models, including Reynolds-Averaged Navier-Stokes (RANS), Large Eddy Simulation (LES), and Variational Multi-Scale (VMS); time-marching schemes; methods to solve system of linear equations (e.g. GMRES, Conjugate Gradient); grid generation and adaptation; and post-processing of the solution using VisIt and ParaView. Also includes an introduction to parallel computing.
Course Hours:
3 units; (3-2)
Antirequisite(s):
Credit for Mechanical Engineering 672 and and any of 519.04 (Computational Fluid Dynamics), 572 or 619.22 (Computational Fluid Dynamics) will not be allowed.
|
back to top | |
|
Mechanical Engineering
674
|
Gas and Liquid Hydraulics
|
|
Properties of liquids and gases, steady-state, transient, multiphase, pressure drop due to friction, pressure required to transport, liquid pumping and gas compression, valves and flow measurement.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
675
|
Materials Selection and Metallurgy
|
|
Fundamentals of physical metallurgy of carbon steels. Principles of steel strengthening. Evolution of pipeline steels. Composition, microstructures and properties of low- and high-grade pipeline steels. Thermo-mechanical controlling processing of high-strength pipeline steels. Performance and failure of pipeline steels in service.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
676
|
Pipeline Stress Analysis
|
|
Introduction to the stress analysis and design of buried pipelines. Allowable working stress design and strain-based design. Considerations such as operating pressure/temperature, buoyancy, buckling, and pipe-soil interaction are examined. Pipeline flexibility analysis is explored using both analytical and numerical methods. Mitigation strategies for pipelines are discussed. The pertinent requirements of the current North American pipeline codes are addressed.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
677
|
Geotechnical Aspects in Pipeline Engineering
|
|
Soil types and classification, soil testing, soil strength-deformation determination, safe burial depth, ground movement in on-shore and offshore, loading pattern on pipelines, soil-pipe interaction and monitoring (in moving slopes, muskeg, permafrost, seabed, and river crossing), performance assessment of pipelines under different in situ environmental loading, ALA and PRCI design guidelines.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
678
|
Environmental Impact and Regulatory Matters
|
|
Examines pipelines as linear assets which cross a wide variety of ecosystems and communities; public concerns about health, safety, archeological and environmental protection, and participation of stakeholders with diverse interests, including First Nations; and the complexity of regulatory processes. Topics include environmental impact assessment, public consultation and roles and responsibility of regulators.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
680
|
Operation and Maintenance
|
|
Automation overview, SCADA systems, station control, instrumentation and metering, custody transfer, nominations process, scheduling and batching multi products. Recommended practices for land usage, ROW patrols, pipeline repair: protocols; repair methods; codes and standards; reference technical papers.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
682
|
Automation and Control Systems
|
|
The basics of industrial automation and control systems, with an emphasis on their application to the energy industry in the areas of safety and energy savings. The key technologies considered will be programmable logic controllers (PLC), supervisory control and data acquisition (SCADA) systems, and distributed control systems (DCS).
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
683
|
Applications of 3D Rigid Body Mechanics in Biomechanics
|
|
Applications of 3D motion analysis and rigid body mechanics to musculoskeletal system locomotion, and movement. Experimental, theoretical and numerical methods for optical motion imaging, 3D analysis of joint kinematics and kinetics, joint angle representations, prediction of joint forces, data analysis and filtering, error propagation, inverse and forward dynamics approaches, and applications to clinical and orthopaedic engineering.
Course Hours:
3 units; (3-0)
|
back to top | |
|
Mechanical Engineering
684
|
Corrosion, Cracking, and Coatings
|
|
Electrochemical principles of corrosion reactions. Internal and external corrosion of buried pipelines. Principle of cathodic protection. Evolution of pipeline coating technology. Coating performance in conjunction with cathodic protection. Failure modes and effect analysis of pipeline coatings. Stress corrosion cracking of pipelines, along with corrosion fatigue and hydrogen-induced cracking of pipeline steels.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
685
|
Biomechanics of Human Movement
|
|
Introduction to the measuring methods (accelerometry, goniometry, film and film analysis, video systems) of biomechanical analysis of human movement (force and force distribution). Description of the mechanical properties of bone, tendon, ligaments, cartilage, muscles and soft tissues. The relation between structure and function of biomaterials. Introduction to descriptive analysis of human movement.
Course Hours:
3 units; (3-3)
Prerequisite(s):
Consent of the Department.
Antirequisite(s):
Credit for Mechanical Engineering 685 and either Kinesiology 685 or Medical Science 685 will not be allowed.
|
back to top | |
|
Mechanical Engineering
686
|
Integrity Management
|
|
Overview and implementation of the integrity management program, threat management, failure mode identification, baseline assessment plan, fitness-for-service assessment using direct assessment and condition monitoring such as inline inspections and pressure testing; defects; defect analysis; risk reduction approaches and corrective actions, upgrading.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
688
|
Pipeline In-Line Inspection Technologies
|
|
Traditional in-line inspection (ILI) methods, including ultrasonic, EMAT, and MFL, and non-traditional ILI methods, such as eddy current, INS, and acoustic. Non-piggable lines. Discrepancies between reported vs. actual defects and anomalies.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
689
|
Pipeline Leak Detection Technologies
|
|
Computational pipeline monitoring (CPM) methods and external leak detection techniques, such as fiber optic, acoustic, and polymeric composite sensors. The internal leak detection methods include volume balance, rate of changes, real time transient model (RTTM), and negative pressure.
Course Hours:
1 unit; (12 hours)
Prerequisite(s):
Admission to the Graduate Certificate in Pipeline Engineering.
|
back to top | |
|
Mechanical Engineering
698
|
Graduate Project
|
|
Individual project in the student's area of specialization under the guidance of the student's supervisor. A written proposal, one or more written progress reports, and a final written report are required. An oral presentation is required upon completion of the course.
Course Hours:
6 units; (0-4)
Prerequisite(s):
Consent of the Department.
|
back to top | |
|
Mechanical Engineering
699
|
Vibration and Machine Dynamics
|
|
Linear vibration theory: free and forced vibration of single- and multi- degree-of-freedom systems; damping in machines; vibration absorbers; experimental modal analysis. Balance of rotating machinery: sources of unbalance, rigid rotors, flexible rotors, critical speeds, balancing principles. Lagrange equations: application to mechanical systems. Signal analysis: time and frequency domain. Introduction to statistical signal analysis. Vibration measurement and analysis for condition monitoring.
Course Hours:
3 units; (3-1T-3/2)
Antirequisite(s):
Credit for Mechanical Engineering 699 and 599 will not be allowed.
|
back to top | |
|
Mechanical Engineering
708
|
Turbulence
|
|
Provides an overview of turbulence in incompressible flows of Newtonian fluids. Topics include: the nature of turbulence; classical methods of analysis (Reynolds-averaging, spectral representations); the concept of scales; a review of isotropic and homogeneous turbulence; the energy cascade and the role of vorticity in turbulence canonical flows: boundary layers, jets, wakes and mixing layers; modern views of turbulence including coherent motions and inter-scale energy transfer.
Course Hours:
3 units; (4-0)
|
back to top | |
|
Mechanical Engineering
713
|
Research Seminar II
|
|
Students will develop written and oral communication skills required to disseminate their technical research results and to receive formative feedback on performance.
Course Hours:
3 units; (3S-0)
NOT INCLUDED IN GPA
|
back to top | |
|